Mini-Split Installation in Tishomingo County, Mississippi
A mini-split heats and cools a space without ductwork. We install Gree mini-splits in garages, shops, porches, bedrooms and additions, and we finish the outside so it looks like it belongs there.
Need a repair instead? Request Service
Mini-Splits
Garages and shops
Two Gree mini-splits keep a large garage comfortable year-round on one of our jobs. We have also added a mini-split to a shop.
Porches, bedrooms and additions
An 18,000 BTU Gree mini-split turned an enclosed back porch into a room that is usable all year. We have installed them in a bedroom and an addition too.
Line hide
The line set on the outside wall is covered with line hide. It protects the lines and gives a clean finished look.
Wall-mounted outdoor units
Where it suits the house, the outdoor unit is mounted on the wall instead of sitting on the ground.
Disconnect, surge protection, sealed penetrations
A proper electrical disconnect, a surge protector, and the wall penetration sealed.
Cleaning and repair
We break down and deep clean the indoor head, the coil, the blower wheel and the drain line. We have also restored a unit with a new blower motor instead of replacing it.
The numbers people ask about first.
- Equipment we install
- Gree mini-splitsAs shown in our project photos.
- Spaces
- Garage, shop, porch, bedroom, additionRooms with no ductwork, or rooms that never stay the right temperature.
- Recent porch job
- 18,000 BTUOne indoor head on an enclosed back porch.
- Recent garage job
- Two systemsOne head on each side of a large garage.
- Outside finish
- Line hide and a wall mountWith a disconnect and a surge protector.
- Estimate
- FreeCall or message (662) 660-3380.
These describe our own recent jobs. The size your space needs depends on the room, and we set it when we look at it.
From rough and exposed to clean and protected
A mini-split can work fine and still look unfinished: lines loose on the siding, the outdoor unit on the ground, the hole in the wall open. We have been called to clean up installs like that. We add line hide, mount the outdoor unit, tidy the electrical and refrigerant lines, seal the penetration and add a surge protector. Our own installs get that finish from the start.
How we workWhere the outdoor unit goes
It needs an outside wall or a pad near the room it serves. We will pick the spot with you.
One head or two
A large or divided space may need more than one. The big garage in our projects has two.
Keep it clean
Mini-splits collect dust and buildup in the blower wheel and coil over time. That can mean weak airflow, musty smells and higher power bills.
A repair may be enough
Not every mini-split with a problem needs to be replaced. A new blower motor put one of ours back to work.
How a job runs.
- 01
Call
Call or message (662) 660-3380. A local company answers the phone.
- 02
Look
We look at the equipment, the ductwork and the electrical, and tell you when a repair makes more sense than a replacement.
- 03
Estimate
Free estimate on new systems.
- 04
Install or repair
A new pad or wall mount where it is needed, sealed duct connections, and a new disconnect and surge protector on installs.
- 05
Finish
Line sets covered, penetrations sealed, the site left clean.
Our work, before and after.
Two Gree mini-splits for a large garage
Two Gree mini-splits heat and cool a large garage.
- Equipment
- Two Gree mini-splits
- Finish
- Line sets covered with line hide
18,000 BTU Gree mini-split for a back porch
An 18,000 BTU Gree mini-split makes an enclosed back porch usable year-round.
- Equipment
- Gree mini-split
- Capacity
- 18,000 BTU
Mini-split install cleaned up with line hide and a wall mount
An existing mini-split install cleaned up: outdoor unit wall-mounted, line hide added, electrical and refrigerant lines tidied.
- Scope
- Line hide, wall mount, electrical and refrigerant lines cleaned up
Questions we get.
Can a mini-split heat and cool a garage or shop?
Yes. A mini-split both heats and cools, and it needs no ductwork. We have installed them in a large garage and in a shop for year-round use.
What is line hide on a mini-split?
Line hide is a cover that runs over the refrigerant lines, drain and wiring on the outside wall. It protects the line set from weather and gives the install a finished look. We use it on our mini-split installs.
Why does my mini-split smell musty?
Usually because dust, mold and buildup have collected in the blower wheel and coil of the indoor head. A full breakdown and deep cleaning of the head, coil, blower wheel and drain line takes care of it.
How often should a mini-split be cleaned?
Follow the schedule in the owner’s manual for your unit, and have it deep cleaned when you notice weak airflow, a musty smell or a higher power bill. If yours has not been cleaned in a while, it is time.
What size mini-split do I need for a porch?
It depends on the size of the porch, the windows and how well it is closed in. The enclosed back porch in our projects took an 18,000 BTU unit. We will look at yours and size it during a free estimate.
Can you fix a mini-split another company installed?
Yes. We repair and clean mini-splits, and we can tidy up an existing install with line hide and a wall mount.
Tishomingo Co. · Itawamba Co. · Prentiss Co. · Lee Co. · Alcorn Co. · Hardin Co. TN · McNairy Co. TN
Tell us about the job.
Send the basics and we will follow up.
Something broken now? Request Service